Anti-torpedo Bulge

The anti-torpedo bulge (also known as an anti-torpedo blister) is a form of defence against naval torpedoes occasionally employed in warship construction in the period between the First and Second World Wars. It involved fitting (or retrofitting) partially water-filled compartmentalized sponsons on either side of a ship's hull, intended to detonate torpedoes, absorb their explosions, and contain flooding to damaged areas within the bulges.

Application

Essentially, the bulge is a compartmentalized, below the waterline sponson isolated from the ship's internal volume. It is part air-filled, and part free-flooding. In theory, a torpedo strike will rupture and flood the bulge's outer air-filled component while the inner water-filled part dissipates the shock and absorbs explosive fragments, leaving the ship's main hull structurally intact. Transverse bulkheads within the bulge limit flooding to the damaged area of the structure.

The bulge was developed by the British Director of Naval Construction, Eustace Tennyson-D'Eyncourt, who had four old ''Edgar''-class protected cruisers so fitted in 1914. These ships were used for shore bombardment duties, and so were exposed to inshore submarine and torpedo boat attack. ''Grafton'' was torpedoed in 1917, and apart from a few minor splinter holes, the damage was confined to the bulge and the ship safely made port. ''Edgar'' was hit in 1918; this time damage to the elderly hull was confined to dented plating.

The Royal Navy had all new construction fitted with bulges from 1914, beginning with the ''Revenge''-class battleships and ''Renown''-class battlecruisers. It also had its large monitors fitted with enormous bulges. This was fortunate for ''Terror'', which survived three torpedoes striking the hull forward, and for her sister ''Erebus'', which survived a direct hit from a remotely-controlled explosive motor boat that ripped off of her bulge. On the other hand, the bulges to nearly led to a disaster in Dover Harbour on 11 September 1918. ''Glatton'' caught fire in her cordite magazine and had the potential to explode in proximity to a loaded ammunition ship. The admiral on hand ordered the monitor scuttled to prevent a catastrophic explosion. The first attempt to do so with torpedoes failed due to the protective effect of the bulges. Half an hour later, a larger, more powerful torpedo was able to sink ''Glatton'' by striking the hole caused by the initial, ineffective hit.

Older ships also had bulges incorporated during refit, such as the U.S. Navy's , laid down during World War I and retrofitted 1929-31. Japan's ''Yamashiro'' had them added in 1930.

Later designs of bulges incorporated various combinations of air and water filled compartments and packing of wood and sealed tubes. As bulges increased a ship's beam, they caused a reduction in speed, which is a function of the length-to-beam ratio. Therefore, various combinations of narrow and internal bulges appeared throughout the 1920s and into the 1930s. The external bulge had disappeared from construction in the 1930s, being replaced by internal arrangements of compartments with a similar function. An additional reason for the bulges' obsolescence was advances in torpedo design. In particular, deployment of magnetic pistol and magnetic proximity fuze in the early 1940s allowed torpedoes to run beneath a target's hull and explode there, beyond the bulges, rather than needing to strike the side of the ship directly. However, older ships were still being fitted with new external bulges through World War II, particularly US ships. In some cases this was to restore buoyancy to compensate for wartime weight additions, as well as for torpedo protection.

See also

* Torpedo belt, a later development of torpedo defense system. Essentially a torpedo bulge built on the inside of the hull so as to not protrude and cause unnecessary drag.
* Torpedo net, earlier torpedo defense system - far more effective, but could only be used whilst stationary.
* Spaced armor, a similar concept used primarily on tanks and armored cars.

Footnotes

Citations

Bibliography

*
* {{cite book , last1=Buxton , first1=Ian , title=Big Gun Monitors: Design, Construction and Operations 1914-1945 , year=2008 , publisher=Naval Institute Press , location=Annapolis, MD , isbn=978-1-59114-045-0 , edition=2nd, revised and expanded
, orig-year=1978
, ref={{harvid, Buxton, 1978

External links

St. Petersburg Daily Times - Mar 2, 1919 - Blister stops explosion of sub torpedoes

Naval armour
Naval architecture
Anti-submarine warfare